Arduino Pachube Клиент

Източник:  arduino.cc

Превод:  Т. Б.

Този пример Ви показва, как да отговорите на HTTP заявка, чрез Ethernet shield.
По специално, то се свързва към „pachube.com“, един безплатен сайт за събиране на информация от сензори (datalogging).
Този пример изисква от вас да си създадете акаунт в „pachube.com“, а също така да си създадете „pachube feed“
(за повече информация относно настройването на входен feed, моля кликнете > тук <).
Вашият Ethernet shield след това ще се свърже към този feed и ще качва там информация от сензора на всеки 10 секунди.

ХАРДУЕРНИ ИЗИСКВАНИЯ

+ Arduino Ethernet Shield или Arduino Ethernet
+ Shield-съвместим с Arduino платката
+ Един аналогов сензор свързан към Ethernet shield-да

СОФТУЕРНИ ИЗИСКВАНИЯ

+ Акаунт в pachube.com
+ Feed в patchube.com, който приема два информационни обекта

СХЕМА

Ethernet shield-да Ви позволява да свържете WizNet Ethernet контролера към Arduino посредством шината SPI.
Той използва изводи с номера 10,11,12 и 13 за SPI връзката към WizNet. По-късните модели на Ethernet shiеld
притежават също така вградена SD карта.
Цифровият „извод 4-ти“ се използа, за да се контролира „извода за контрол над подчинените устройства“ (Slave Select) върху SD картата.

Shield-да трябва да се свърже към мрежа чрез ethernet кабел. Ще се наложи да промените настройките в кода, за да отговарят
на вашите мрежова конфигурация.

*** изображението е проектирано чрез Fritzing. За повече примерни схеми, моля погледнете официялната страница на проекта „Fritzing project“.
В горното изображение, вашата Arduino платка трябва да се постави точно под „Ethernet shield“-да.

 

СХЕМА

На картината: Една CDS фотоклетка с „Изтеглящ-Надолу“ 10k Резистор, свързан към аналоговия извод-0.

 

СОРС КОД

// Начало на кода

/*
Pachube sensor client

This sketch connects an analog sensor to Pachube (http://www.pachube.com)
using a Wiznet Ethernet shield. You can use the Arduino Ethernet shield, or
the Adafruit Ethernet shield, either one will work, as long as it’s got
a Wiznet Ethernet module on board.

This example has been updated to use version 2.0 of the Pachube.com API.
To make it work, create a feed with a datastream, and give it the ID
sensor1. Or change the code below to match your feed.

Circuit:
* Analog sensor attached to analog in 0
* Ethernet shield attached to pins 10, 11, 12, 13

created 15 March 2010
modified 9 Apr 2012
by Tom Igoe with input from Usman Haque and Joe Saavedra

http://arduino.cc/en/Tutorial/PachubeClient
This code is in the public domain.

*/

#include <SPI.h>
#include <Ethernet.h>

#define APIKEY „YOUR API KEY GOES HERE“ // replace your pachube api key here
#define FEEDID 00000 // replace your feed ID
#define USERAGENT „My Project“ // user agent is the project name

// assign a MAC address for the ethernet controller.
// Newer Ethernet shields have a MAC address printed on a sticker on the shield
// fill in your address here:
byte mac[] = {
0xDE, 0xAD, 0xBE, 0xEF, 0xFE, 0xED};

// fill in an available IP address on your network here,
// for manual configuration:
IPAddress ip(10,0,1,20);
// initialize the library instance:
EthernetClient client;

// if you don’t want to use DNS (and reduce your sketch size)
// use the numeric IP instead of the name for the server:
IPAddress server(216,52,233,122); // numeric IP for api.pachube.com
//char server[] = „api.pachube.com“; // name address for pachube API

unsigned long lastConnectionTime = 0; // last time you connected to the server, in milliseconds
boolean lastConnected = false; // state of the connection last time through the main loop
const unsigned long postingInterval = 10*1000; //delay between updates to Pachube.com

void setup() {
// Open serial communications and wait for port to open:
Serial.begin(9600);
while (!Serial) {
; // wait for serial port to connect. Needed for Leonardo only
}

// start the Ethernet connection:
if (Ethernet.begin(mac) == 0) {
Serial.println(„Failed to configure Ethernet using DHCP“);
// DHCP failed, so use a fixed IP address:
Ethernet.begin(mac, ip);
}
}

void loop() {
// read the analog sensor:
int sensorReading = analogRead(A0);

// if there’s incoming data from the net connection.
// send it out the serial port. This is for debugging
// purposes only:
if (client.available()) {
char c = client.read();
Serial.print(c);
}

// if there’s no net connection, but there was one last time
// through the loop, then stop the client:
if (!client.connected() && lastConnected) {
Serial.println();
Serial.println(„disconnecting.“);
client.stop();
}

// if you’re not connected, and ten seconds have passed since
// your last connection, then connect again and send data:
if(!client.connected() && (millis() – lastConnectionTime > postingInterval)) {
sendData(sensorReading);
}
// store the state of the connection for next time through
// the loop:
lastConnected = client.connected();
}

// this method makes a HTTP connection to the server:
void sendData(int thisData) {
// if there’s a successful connection:
if (client.connect(server, 80)) {
Serial.println(„connecting…“);
// send the HTTP PUT request:
client.print(„PUT /v2/feeds/“);
client.print(FEEDID);
client.println(„.csv HTTP/1.1“);
client.println(„Host: api.pachube.com“);
client.print(„X-PachubeApiKey: „);
client.println(APIKEY);
client.print(„User-Agent: „);
client.println(USERAGENT);
client.print(„Content-Length: „);

// calculate the length of the sensor reading in bytes:
// 8 bytes for „sensor1,“ + number of digits of the data:
int thisLength = 8 + getLength(thisData);
client.println(thisLength);

// last pieces of the HTTP PUT request:
client.println(„Content-Type: text/csv“);
client.println(„Connection: close“);
client.println();

// here’s the actual content of the PUT request:
client.print(„sensor1,“);
client.println(thisData);

}
else {
// if you couldn’t make a connection:
Serial.println(„connection failed“);
Serial.println();
Serial.println(„disconnecting.“);
client.stop();
}
// note the time that the connection was made or attempted:
lastConnectionTime = millis();
}

// This method calculates the number of digits in the
// sensor reading. Since each digit of the ASCII decimal
// representation is a byte, the number of digits equals
// the number of bytes:

int getLength(int someValue) {
// there’s at least one byte:
int digits = 1;
// continually divide the value by ten,
// adding one to the digit count for each
// time you divide, until you’re at 0:
int dividend = someValue /10;
while (dividend > 0) {
dividend = dividend /10;
digits++;
}
// return the number of digits:
return digits;
}

// Край на кода